35w Electronic ballast for hid
10W LED Driver
MOQ :1 个
Lead Time :5 Days
Seller Support : Trade Authenticity Guaranteed & Accepting
Payment : T/T
Departure Port : Shanghai,Guangzhou,Shenzhen
Product details
Supply Ability
- Supply Ability:10000 piecesWarranty(Year):1 Year
Packaging & Delivery
- Packaging: 个
Product Specifications
Product Description
Item Note1 Model | YAC-10-350-A1 | |||||
Output | Rated Voltage | 30VDC | ||||
Maximum Voltage | 34VDC | |||||
Voltage Range (under the mode of constant current CC) | 18V~30VDC | |||||
Rated Current (constant current) | 330mA | |||||
Rated Power | 10W | |||||
Adaptability to Load (the precent of the rated power) | 70%~114% | |||||
Ripple & Noise (Max.) note2 | <10% | |||||
Voltage Tolerance/Current Tolerance | ±6%/±6% | |||||
Setup Time note5 | 10mS | |||||
Hold Time (typical) | 10mS | |||||
Input | Voltage Range note7 | 100VAC~264VAC | ||||
Input Frequency Range | 43HZ~63HZ | |||||
Power Factor (typical) | >0.95 | |||||
Efficiency (typical) | >84% | |||||
Alternating Current | 0.05~0.2A | |||||
Start Instantaneous Current (Max.) | Cold start 20A | |||||
Standby Power (Average) | <0.05W | |||||
Protection | Output Short Circuit note 9 | Drivers use burp protection mode intermittently. After clearing of faults, get back to work. | ||||
note 10 | ||||||
Output Pressure note 10 | ||||||
Load Voltage note 10 | constant-current control | |||||
Over Temperature note 6 | ||||||
Special Function | Delayed Downrating Function note 8 | Nothing | ||||
Environment | Regular Working Temperature note 8 | -25℃~60℃ | ||||
Waterproof Grade | ||||||
Storage Temperature, Humidity | -40℃~+85℃,10~95%RH | |||||
Vibration | ||||||
Noise | Match GB/T14623 | |||||
Safety & EMC | Safety Standards note 4 | EN61347-1;EN61347-2-13 | ||||
Lighting Protection of Surge | ||||||
Withstand Voltage | I/P-O/P:1.5KVAC I/P-FG:1.0KVAC O/P-FG:0.5KVAC | |||||
Isolationg Resistance | I/P-O/P,I/P-FG,O/P-FG:100M Ohms/500VDC/25℃/70% RH | |||||
EMC Emission note 4 | EN55015; GB17743 | |||||
Harmonic Power (Max.) | ||||||
Note | 1.All parameters not specially mentioned are measured at 220VAC(50Hz) input, rated load and 25℃ of ambient temperature. | |||||
2.Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. | ||||||
3.Constant current operation region is within 80%-100% rated output voltage. This is the suitable operation region for LED related applications. We suggest that do not long-term use of overpower. | ||||||
4.Safety & EMC design fit for CE & CQC certification. | ||||||
5.Setup time length will be measured in the first time cold start. Swith on/off may lead to the increase of initial adjustment time(Frequently switch on /off may lead to power protection). | ||||||
6.Operation temperature error is between ±5℃. We can set temperature protection value according to customers' requirement. | ||||||
7.Please do not exceed the input voltage range. The power can not be started properly when the input voltage lower than 85VAC. The light will flash and power supply will be damaged when the input voltage higher than 305VAC. | ||||||
8.We can customize LED drivers, the tolerance environment temperature of which is between -40℃~+85℃. | ||||||
9."Burp" means the power supply will work for some time, and then stop for some time. It is similar to someone in "burp" situation. This power supply's burp protection state is to work for 7.5uS, and stop for 350uS. | ||||||
10.When the driver turns off the protection, it should judge the power input, remove failures and connect the load. After cut off the input for 15s, power on again, the LED load will re-start reliably. |
You May Like
- Free Member
- Trade Assurance
Business Type : Manufacturer,Exporter,Wholesaler
Company Location:
Year Established: 25YRS